Ammonium metavanadate
Product identifier
- Product name: Ammonium metavanadate
- CBnumber: CB8854364
- CAS: 7803-55-6
- EINECS Number: 232-261-3
- Synonyms: AMMONIUM METAVANADATE,NH4VO3
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 400-158-6606
Classification of the substance or mixture
Acute toxicity - Category 3, Oral
Eye irritation, Category 2
Acute toxicity - Category 4, Inhalation
Reproductive toxicity, Category 2
Specific target organ toxicity – repeated exposure, Category 1
Hazardous to the aquatic environment, long-term (Chronic) - Category Chronic 2
Label elements
Pictogram(s)
- Signal wordDanger
H301 Toxic if swalloed
H302 Harmful if swallowed
H313 May be harmful in contact with skin
H314 Causes severe skin burns and eye damage
H315 Causes skin irritation
H319 Causes serious eye irritation
H330 Fatal if inhaled
H332 Harmful if inhaled
H335 May cause respiratory irritation
H341 Suspected of causing genetic defects
H372 Causes damage to organs through prolonged or repeated exposure
H411 Toxic to aquatic life with long lasting effects
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P320 Specific treatment is urgent (see … on this label).
P330 Rinse mouth.
P303+P361+P353 IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.
P304+P340 IF INHALED: Remove victim to fresh air and Keep at rest in a position comfortable for breathing.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
P405 Store locked up.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P264 Wash ... thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P271 Use only outdoors or in a well-ventilated area.
P203 Obtain, read and follow all safety instructions before use.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P273 Avoid release to the environment.
P301+P316 IF SWALLOWED: Get emergency medical help immediately.
P321 Specific treatment (see ... on this label).
P330 Rinse mouth.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P317 Get medical help.
P318 IF exposed or concerned, get medical advice.
P319 Get medical help if you feel unwell.
P391 Collect spillage.
P405 Store locked up.
P501 Dispose of contents/container to an appropriate treatment and disposal facility in accordance with applicable laws and regulations, and product characteristics at time of disposal.
Other hazards
no data available
Substance
- Product name: Ammonium metavanadate
- Synonyms: AMMONIUM METAVANADATE,NH4VO3
- CAS: 7803-55-6
- EC number: 232-261-3
- MF: H4NO3V
- MW: 116.98
Description of first aid measures
If inhaledMove the victim into fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial respiration and consult a doctor immediately. Do not use mouth to mouth resuscitation if the victim ingested or inhaled the chemical.
Take off contaminated clothing immediately. Wash off with soap and plenty of water. Consult a doctor.
Rinse with pure water for at least 15 minutes. Consult a doctor.
Rinse mouth with water. Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a doctor or Poison Control Center immediately.
Most important symptoms and effects, both acute and delayed
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]: TOXIC; inhalation, ingestion or skin contact with material may cause severe injury or death. Contact with molten substance may cause severe burns to skin and eyes. Avoid any skin contact. Effects of contact or inhalation may be delayed. Fire may produce irritating, corrosive and/or toxic gases. Runoff from fire control or dilution water may be corrosive and/or toxic and cause pollution. (ERG, 2016)
Indication of any immediate medical attention and special treatment needed
Immediate first aid: Ensure that adequate decontamination has been carried out. If patient is not breathing, start artificial respiration, preferably with a demand valve resuscitator, bag-valve-mask device, or pocket mask, as trained. Perform CPR if necessary. Immediately flush contaminated eyes with gently flowing water. Do not induce vomiting. If vomiting occurs, lean patient forward or place on the left side (head-down position, if possible) to maintain an open airway and prevent aspiration. Keep patient quiet and maintain normal body temperature. Obtain medical attention. Poisons A and B
Extinguishing media
Suitable extinguishing media: Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Specific Hazards Arising from the Chemical
Excerpt from ERG Guide 154 [Substances - Toxic and/or Corrosive (Non-Combustible)]: Non-combustible, substance itself does not burn but may decompose upon heating to produce corrosive and/or toxic fumes. Some are oxidizers and may ignite combustibles (wood, paper, oil, clothing, etc.). Contact with metals may evolve flammable hydrogen gas. Containers may explode when heated. For electric vehicles or equipment, ERG Guide 147 (lithium ion batteries) or ERG Guide 138 (sodium batteries) should also be consulted. (ERG, 2016)
Advice for firefighters
Wear self-contained breathing apparatus for firefighting if necessary.
NFPA 704
| HEALTH | 3 | Short exposure could cause serious temporary or moderate residual injury (e.g. liquid hydrogen, sulfuric acid, calcium hypochlorite, hexafluorosilicic acid) | |
| FIRE | 1 | Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia) | |
| REACT | 1 | Normally stable, but can become unstable at elevated temperatures and pressures (e.g. propene) | |
| SPEC. HAZ. |
Personal precautions, protective equipment and emergency procedures
Avoid dust formation. Avoid breathing mist, gas or vapours.Avoid contacting with skin and eye. Use personal protective equipment.Wear chemical impermeable gloves. Ensure adequate ventilation.Remove all sources of ignition. Evacuate personnel to safe areas.Keep people away from and upwind of spill/leak.
Environmental precautions
Prevent further spillage or leakage if it is safe to do so. Do not let the chemical enter drains. Discharge into the environment must be avoided.
Methods and materials for containment and cleaning up
ACCIDENTAL RELEASE MEASURES: Personal precautions, protective equipment and emergency procedures: Wear respiratory protection. Avoid dust formation. Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Evacuate personnel to safe areas. Avoid breathing dust. Environmental precautions: Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Methods and materials for containment and cleaning up: Pick up and arrange disposal without creating dust. Sweep up and shovel. Keep in suitable, closed containers for disposal.
Precautions for safe handling
Handling in a well ventilated place. Wear suitable protective clothing. Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Use non-sparking tools. Prevent fire caused by electrostatic discharge steam.
Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place. Moisture sensitive. Keep in a dry place.
Control parameters
Occupational Exposure limit values| Component | Ammonium trioxovanadate |
|---|---|
| CAS No. | 7803-55-6 |
|
Recommended Exposure Limit: 15 Minute Ceiling value: 0.05 mg V/cu m. /Vanadium dust; The REL applies to all vanadium compounds except vanadium metal and vanadium carbide./ |
no data available
Exposure controls
Ensure adequate ventilation. Handle in accordance with good industrial hygiene and safety practice. Set up emergency exits and the risk-elimination area.
Individual protection measures
Eye/face protectionWear tightly fitting safety goggles with side-shields conforming to EN 166(EU) or NIOSH (US).
Wear fire/flame resistant and impervious clothing. Handle with gloves. Gloves must be inspected prior to use. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.
If the exposure limits are exceeded, irritation or other symptoms are experienced, use a full-face respirator.
no data available
Information on basic physicochemical properties
- Physical stateSolid
- ColourWhite to yellow
- Odour
no data available
- Melting point/freezing point
690 °C
- Boiling point or initial boiling point and boiling range
210 °C
- Flammability
no data available
- Lower and upper explosion limit/flammability limit
no data available
- Flash point
no data available
- Auto-ignition temperature
no data available
- Decomposition temperature
no data available
- pH7 (5.1g/l, H2O, 20℃)
- Kinematic viscosity
no data available
- SolubilityH2O: soluble
- Partition coefficient n-octanol/water
no data available
- Vapour pressure
no data available
- Density and/or relative density2.33
- Relative vapour density2.33
- Particle characteristics
no data available
Reactivity
Slightly soluble in water.
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
NonflammableAcidic inorganic salts, such as AMMONIUM METAVANADATE, are generally soluble in water. The resulting solutions contain moderate concentrations of hydrogen ions and have pH's of less than 7.0. They react as acids to neutralize bases. These neutralizations generate heat, but less or far less than is generated by neutralization of inorganic acids, inorganic oxoacids, and carboxylic acid. Ammonium metavanadate is a weak oxidizing agent, and may react with strong or weak reducing agents to generate heat and products that may be flammable, combustible, or otherwise reactive.
Conditions to avoid
no data available
Incompatible materials
Incompatible materials: Strong acids and oxidizing agents.
Hazardous decomposition products
When heated to decompostion it emits toxic fumes of /ammonia, vanadium, and nitrogen oxides/.
Acute toxicity
- Oral: LD50 - rat (male) - 218.1 mg/kg bw. Remarks:LD50 after 14 days; Slope: 14.98.
- Inhalation: LC50 - rat (male) - 2.61 mg/L air (analytical).
- Dermal: LD50 - rat (male) - > 2 500 mg/kg bw.
Skin corrosion/irritation
no data available
Serious eye damage/irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
no data available
Reproductive toxicity
no data available
STOT-single exposure
no data available
STOT-repeated exposure
no data available
Aspiration hazard
no data available
Toxicity
- Toxicity to fish: LC50 - Leuciscus idus - 693 μg/L - 96 h. Remarks:V.
- Toxicity to daphnia and other aquatic invertebrates: LC50 - Daphnia magna - 1 520 μg/L - 48 h. Remarks:V.
- Toxicity to algae: EC50 - Desmodesmus subspicatus (previous name: Scenedesmus subspicatus) - 2 907 μg/L - 72 h.
- Toxicity to microorganisms: EC50 - activated sludge of a predominantly domestic sewage - > 100 mg/L - 3 h. Remarks:V.
Persistence and degradability
no data available
Bioaccumulative potential
no data available
Mobility in soil
Log Kd values for ammonium vanadate determined in 11 soils from 10 soil orders were as follows(1):Log Kd Soil type Soil characteristics State of origin 2.152 Alligator pH 4.8, 1.54% TOC, 5.9% sand, 39.4% silt, 54.7% clay Louisiana 1.035 Calciorthid pH 8.5, 0.44% TOC, 70.0% sand, 19.3% silt, 10.7% clay New Mexico 1.599 Cecil pH 5.7, 0.61% TOC, 78.8% sand, 12.9% silt, 8.3% clay South Carolina 3.347 Kula pH 5.9, 6.62% TOC, 73.7% sand, 25.4% silt, 0.9% clay Hawaii 2.012 Lafitte pH 3.9, 11.6% TOC, 60.7% sand, 21.7% silt, 17.6% clay Louisiana 2.703 Molokai pH 6.0, 1.67% TOC, 25.7% sand, 46.2% silt, 28.2% clay Hawaii 1.270 Norwood pH 6.9, 0.21% TOC, 79.2% sand, 18.1% silt, 2.8% clay Louisiana 1.960 Olivier pH 6.6, 0.83% TOC, 4.4% sand, 89.4% silt, 6.2% clay Louisiana 1.958 Spodosol pH 4.3, 1.98% TOC, 90.2% sand, 6.0% silt, 3.8% clay Florida 1.907 Webster pH 7.6, 4.39% TOC, 27.5% sand, 48.6% silt, 23.9% clay Iowa 2.184 Windsor pH 5.3, 2.03% TOC, 76.8% sand, 20.5% silt, 2.8% clay New Hampshire
Other adverse effects
no data available
Disposal methods
ProductThe material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.
UN Number
ADR/RID: UN2859 (For reference only, please check.)
IMDG: UN2859 (For reference only, please check.)
IATA: UN2859 (For reference only, please check.)
UN Proper Shipping Name
ADR/RID: AMMONIUM METAVANADATE (For reference only, please check.)
IMDG: AMMONIUM METAVANADATE (For reference only, please check.)
IATA: AMMONIUM METAVANADATE (For reference only, please check.)
Transport hazard class(es)
ADR/RID: 6.1 (For reference only, please check.)
IMDG: 6.1 (For reference only, please check.)
IATA: 6.1 (For reference only, please check.)
Packing group, if applicable
ADR/RID: II (For reference only, please check.)
IMDG: II (For reference only, please check.)
IATA: II (For reference only, please check.)
Environmental hazards
ADR/RID: Yes
IMDG: Yes
IATA: Yes
Special precautions for user
no data available
Transport in bulk according to IMO instruments
no data available
Safety, health and environmental regulations specific for the product in question
European Inventory of Existing Commercial Chemical Substances (EINECS)Abbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
- IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
- HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
- IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
- eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
- CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
- ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
- ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
- Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
- ECHA - European Chemicals Agency, website: https://echa.europa.eu/
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.