Stannous octoate
Product identifier
- Product name: Stannous octoate
- CBnumber: CB0308694
- CAS: 301-10-0
- EINECS Number: 206-108-6
- Synonyms: stannous octoate,Tin(II) 2-ethylhexanoate
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 400-158-6606
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordDanger
Substance
- Product name: Stannous octoate
- Synonyms: stannous octoate,Tin(II) 2-ethylhexanoate
- CAS: 301-10-0
- EC number: 206-108-6
- MF: C16H30O4Sn
- MW: 405.12
Description of first aid measures
General adviceMost important symptoms and effects, both acute and delayed
Indication of any immediate medical attention and special treatment needed
Extinguishing media
Suitable extinguishing mediaSpecial hazards arising from the substance or mixture
Carbon oxides Tin/tin oxides Combustible.
Vapors are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating.
Development of hazardous combustion gases or vapours possible in the event of fire.
Advice for firefighters
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Further information
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.
NFPA 704
| HEALTH | 2 | Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine) | |
| FIRE | 1 | Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.
Environmental precautions
Do not let product enter drains.
Methods and materials for containment and cleaning up
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully with liquid-absorbent material (e.g.
Chemizorb?). Dispose of properly. Clean up affected area.
Reference to other sections
For disposal see section 13.
Precautions for safe handling
For precautions see section 2.2.
Conditions for safe storage, including any incompatibilities
Storage conditions
Tightly closed.
Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated
control parameter
Hazard composition and occupational exposure limitsExposure controls
Personal protective equipmentUse equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.
Full contact
Material: Nitrile rubber
Minimum layer thickness: 0,11 mm Break through time: 480 min
Material tested:Dermatril? (KCL 740 / Aldrich Z677272, Size M)
Splash contact Material: Nitrile rubber
Minimum layer thickness: 0,11 mm Break through time: 480 min
Material tested:Dermatril? (KCL 740 / Aldrich Z677272, Size M)
data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374
If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the EC approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.
protective clothing
required when vapours/aerosols are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Recommended Filter type: Filter type ABEK
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer.
These measures have to be properly documented.
Do not let product enter drains.
Information on basic physicochemical properties
- Appearancelight yellow viscous liquid
- OdourNo data available
- Odour ThresholdNo data available
- pHNo data available
- Melting point/freezing pointMelting point/range: 9 °C at 1.013,0 hPa - OECD Test Guideline 102
- Initial boiling point and boiling range>200°C
- Flash point113 °C - closed cup
- Evaporation rateNo data available
- Flammability (solid, gas)The product is not flammable. - Pyrophoric properties of solids and liquids
- Upper/lower flammability or explosive limitsNo data available
- Vapour pressure No data available
- Vapour density No data available
- Relative density1,26
- Water solubility4,585 g/l at 20 °C - OECD Test Guideline 105- soluble
- Partition coefficient: n-octanol/waterNo data available
- Autoignition temperature >400 °C at 1010,50 - 1011,10 hPa
- Decomposition temperatureNo data available
- ViscosityViscosity, kinematic: ca.306 mm2/s at 20 °C Viscosity, dynamic: No data available
- Explosive propertiesNo data available
- Oxidizing propertiesNo data available
Other safety information
Surface tension 55,9 mN/m at 20,5 °C
Dissociation constant 5,09 at 20 °C
Reactivity
Forms explosive mixtures with air on intense heating.
A range from approx. 15 Kelvin below the flash point is to be rated as critical.
Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .
Possibility of hazardous reactions
No data available
Conditions to avoid
Strong heating.
Incompatible materials
Strong oxidizing agents
Hazardous decomposition products
In the event of fire: see section 5
Information on toxicological effects
Acute toxicityLD50 Dermal - Rabbit - > 2.000 mg/kg
Remarks: Prolonged skin contact may cause skin irritation and/or dermatitis.
Result: Mild skin irritation - 24 h
Result: Severe eye irritation (OECD Test Guideline 405)
Result: May cause sensitization by skin contact. (OECD Test Guideline 406)
Test system: S. typhimurium
Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 471
Result: negative
Suspected human reproductive toxicant
Toxicity
(OECD Test Guideline 203)
(OECD Test Guideline 201)
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
Other adverse effects
No data available
Waste treatment methods
Product
See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.
UN number
ADR/RID: - IMDG: - IATA: -
UN proper shipping name
Transport hazard class(es)
ADR/RID: - IMDG: - IATA: -
Packaging group
ADR/RID: - IMDG: - IATA: -
Environmental hazards
ADR/RID: no IMDG Marine pollutant: no IATA: no
Special precautions for user
Further information
Not classified as dangerous in the meaning of transport regulations.
Safety, health and environmental regulations/legislation specific for the substance or mixture
Regulations on the Safety Management of Hazardous ChemicalsAbbreviations and acronyms
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- CAS: Chemical Abstracts Service
- EC50: Effective Concentration 50%
- IATA: International Air Transportation Association
- IMDG: International Maritime Dangerous Goods
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- STEL: Short term exposure limit
- TWA: Time Weighted Average
References
【1】CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
【2】ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
【3】ECHA - European Chemicals Agency, website: https://echa.europa.eu/
【4】eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
【5】ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
【6】Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
【7】HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
【8】IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
【9】IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
【10】Sigma-Aldrich, website: https://www.sigmaaldrich.com/
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.