2-(Dimethylamino)ethyl methacrylate
Product identifier
- Product name: 2-(Dimethylamino)ethyl methacrylate
- CBnumber: CB2267524
- CAS: 2867-47-2
- EINECS Number: 220-688-8
- Synonyms: DMAEMA,2-(dimethylamino)ethyl methacrylate
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 400-158-6606
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordDanger
Substance
- Product name: 2-(Dimethylamino)ethyl methacrylate
- Synonyms: DMAEMA,2-(dimethylamino)ethyl methacrylate
- CAS: 2867-47-2
- EC number: 220-688-8
- MF: C8H15NO2
- MW: 157.21
Description of first aid measures
General adviceMost important symptoms and effects, both acute and delayed
Indication of any immediate medical attention and special treatment needed
Extinguishing media
Suitable extinguishing mediaSpecial hazards arising from the substance or mixture
Carbon oxides Nitrogen oxides (NOx) Combustible.
Vapors are heavier than air and may spread along floors. Risk of dust explosion.
Forms explosive mixtures with air on intense heating.
Development of hazardous combustion gases or vapours possible in the event of fire.
Advice for firefighters
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Further information
Remove container from danger zone and cool with water. Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.
NFPA 704
| HEALTH | 2 | Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine) | |
| FIRE | 2 | Must be moderately heated or exposed to relatively high ambient temperature before ignition can occur and multiple finely divided suspended solids that do not require heating before ignition can occur. Flash point between 37.8 and 93.3 °C (100 and 200 °F). (e.g. diesel fuel, sulfur) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition.
Evacuate the danger area, observe emergency procedures, consult an expert. For personal protection see section 8.
Environmental precautions
Do not let product enter drains.
Methods and materials for containment and cleaning up
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up with liquid-absorbent material (e.g. Chemizorb? ). Dispose of properly. Clean up affected area.
Reference to other sections
For disposal see section 13.
Precautions for safe handling
Advice on protection against fire and explosion
Keep away from open flames, hot surfaces and sources of ignition.Take precautionary measures against static discharge.
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
For precautions see section 2.2.
Conditions for safe storage, including any incompatibilities
Storage conditions
Tightly closed. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons.
Storage stability
Recommended storage temperature 2 - 8 °C
Moisture sensitive. Light sensitive.
Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated
control parameter
Hazard composition and occupational exposure limitsExposure controls
Personal protective equipmentUse equipment for eye protection tested and approved under appropriate
government standards such as NIOSH (US) or EN 166(EU). Tightly fitting safety goggles
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Full contact
Material: butyl-rubber
Minimum layer thickness: 0,7 mm Break through time: 480 min Material tested:Butoject? (KCL 898)
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Splash contact Material: Nitrile rubber
Minimum layer thickness: 0,4 mm Break through time: 120 min
Material tested:Camatril? (KCL 730 / Aldrich Z677442, Size M)
protective clothing
Recommended Filter type: Filter A (acc. to DIN 3181) for vapours of organic compounds
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer.
These measures have to be properly documented.
Do not let product enter drains.
Information on basic physicochemical properties
- Appearancelight yellow clear, liquid
- Odouramine-like
- Odour ThresholdNo data available
- pHNo data available
- Melting point/freezing pointMelting point/freezing point: -30 °C at ca.1.013 hPa
- Initial boiling point and boiling range182 - 192 °C - lit.
- Flash point64 °C - closed cup
- Evaporation rateNo data available
- Flammability (solid, gas)No data available
- Upper/lower flammability or explosive limits Lower explosion limit: 1,2 %(V)
- Vapour pressure< 1 hPa at 25 °C
- Vapour density 5,43 - (Air = 1.0)
- Relative densityNo data available
- Water solubility1.000 g/l at 20 °C - miscible
- Partition coefficient: n-octanol/waterlog Pow: 1,13 at 25 °C
- Autoignition temperature200 °C at 1.005 hPa
- Decomposition temperatureNo data available
- ViscosityViscosity, kinematic: 1,47 mm2/s at 20 °C - OECD Test Guideline 114 Viscosity, dynamic: No data available
- Explosive propertiesNo data available
- Oxidizing propertiesNo data available
Other safety information
Dissociation constant 8,44 at 25 °C
Relative vapor density
5,43 - (Air = 1.0)
Reactivity
Forms explosive mixtures with air on intense heating.
A range from approx. 15 Kelvin below the flash point is to be rated as critical.
Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .
Possibility of hazardous reactions
Risk of ignition or formation of inflammable gases or vapours with: Strong oxidizing agents
Violent reactions possible with:
polymerisation initiators peroxi compounds strong reducing agents strong alkalis
Strong acids
Conditions to avoid
Strong heating.
Incompatible materials
rubber, Copper, Strong oxidizing agents
Hazardous decomposition products
In the event of fire: see section 5
Information on toxicological effects
Acute toxicityLD50 Oral - Rat - 1.751 mg/kg
Symptoms: Irritations of mucous membranes in the mouth, pharynx, oesophagus and gastrointestinal tract., Nausea, Vomiting
Remarks: (RTECS) Inhalation
Acute toxicity estimate Dermal - 1.100 mg/kg (Calculation method)
Acute toxicity estimate Dermal - 1.100 mg/kg (Expert judgment)
Acute toxicity estimate Dermal - Expert judgment - 1.100 mg/kg
Result: Causes burns.
Remarks: (ECHA)
Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 476
Result: negative
Test Type: Mutagenicity (mammal cell test): chromosome aberration. Test system: Chinese hamster lung cells
Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 473
Result: Positive results were obtained in some in vitro tests. Test Type: Ames test
Test system: Salmonella typhimurium
Metabolic activation: without metabolic activation Method: OECD Test Guideline 471
Result: Positive results were obtained in some in vitro tests.
Test Type: Micronucleus test Species: Mouse
Application Route: Intraperitoneal Method: OECD Test Guideline 474 Result: negative
Test Type: Micronucleus test Species: Mouse
Application Route: Oral
Method: OECD Test Guideline 474 Result: negative
Toxicity
semi-static test EC50 - Daphnia magna (Water flea) - 33 mg/l - 48 h (OECD Test Guideline 202)
(OECD Test Guideline 201)
Persistence and degradability
Biodegradability aerobic - Exposure time 28 d
Result: 95,3 % - Readily biodegradable. Remarks: (ECHA)
Bioaccumulative potential
No data available
Mobility in soil
No data available
Results of PBT and vPvB assessment
This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
Other adverse effects
Discharge into the environment must be avoided.
Waste treatment methods
Product
See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.
UN number
ADR/RID: 2522 IMDG: 2522 IATA: 2522
UN proper shipping name
ADR/RID: 2-DIMETHYLAMINOETHYL METHACRYLATE
IMDG: 2-DIMETHYLAMINOETHYL METHACRYLATE
IATA: 2-Dimethylaminoethyl methacrylate, stablilized
Transport hazard class(es)
ADR/RID: 6.1 IMDG: 6.1 IATA: 6.1
Packaging group
ADR/RID: II IMDG: II IATA: II
Environmental hazards
ADR/RID: no IMDG Marine pollutant: no IATA: no
Special precautions for user
No data available
Safety, health and environmental regulations/legislation specific for the substance or mixture
Regulations on the Safety Management of Hazardous ChemicalsAbbreviations and acronyms
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- CAS: Chemical Abstracts Service
- EC50: Effective Concentration 50%
- IATA: International Air Transportation Association
- IMDG: International Maritime Dangerous Goods
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- STEL: Short term exposure limit
- TWA: Time Weighted Average
References
【1】CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
【2】ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
【3】ECHA - European Chemicals Agency, website: https://echa.europa.eu/
【4】eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
【5】ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
【6】Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
【7】HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
【8】IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
【9】IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
【10】Sigma-Aldrich, website: https://www.sigmaaldrich.com/
Other Information
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.